抗倍特板材作為高密度的人造板材，質地很堅硬。因此富美家抗倍特廠家認為，即便該板材優點如此多，在加工抗倍特板時應注意一些事項。

As a high-density artificial board, anti Beite board has a hard texture. Therefore, formica anti Beite manufacturers believe that even if the plate has so many advantages, some matters should be paid attention to when processing anti Beite plate.

抗倍特板的優點

Advantages of anti doubling plate

抗倍特板具有較高的彈性模量、抗拉強度和抗彎強度，使其有很高的耐沖擊性;高密度的芯材給予抗倍特板很高的錨固件拔出強度，這種特性對采用螺栓或插件安裝方式的控制臺臺面特別重要，使控制臺臺面具有更高的強度和耐用度。

The high modulus of elasticity, tensile strength and bending strength of the plate make it have high impact resistance; The high-density core material gives high pull-out strength to the anchorage of the anti multiplier plate. This characteristic is particularly important for the console table with bolt or plug-in installation, so that the console table has higher strength and durability.

抗倍特板具有好的耐火性，不會融化、滴落或爆炸，歐洲有關機構將其劃分在有機材料中較高的防火等級，并不會釋放有毒和腐蝕的氣體，這能夠讓控制臺的整體性能更加出色；

The anti Beite board has good fire resistance and will not melt, drip or explode. Relevant European institutions have classified it as a high fire rating among organic materials, and will not release toxic and corrosive gases, which can make the overall performance of the console more excellent;

抗倍特板可長時間保持穩定，其本身具有自潔性，材質致密不會黏附灰塵，清潔簡單，對顏色無任何影響。

The anti Beite board can remain stable for a long time. It has self-cleaning property. The material is dense and will not adhere to dust. It is simple to clean and has no impact on the color.

抗倍特板對于控制臺臺面的使用來講，表面色紙可以是雙面，可滿足不同的客戶對色彩的需求，還具有堅固、抗撞擊、防水、耐潮濕等功能。

For the use of the console table, the surface color paper can be double-sided, which can meet the color needs of different customers. It also has the functions of firmness, impact resistance, waterproof, moisture resistance and so on.

抗倍特板的加工問題

Processing problems of anti magnification plate

對異形邊沿進行加工時，需要先在板件表面劃出所需尺寸，然后使用曲線鋸切割；如果是批量生產，可以在模板的輔助下進行切割，這樣可同時確保加工速度和鋸切質量。

When machining the special-shaped edge, you need to draw the required size on the surface of the plate first, and then use the curve saw to cut; In case of mass production, cutting can be carried out with the help of the template, which can ensure the processing speed and sawing quality at the same time.

加工之前需要清除板件表面的灰塵或異物，以免在板件表面留下劃痕或刻痕。另外鏤銑機的加工速度應保持在2m/min為宜。如果鏤銑刀刀刃角度較小而工件厚度又較厚時，鏤銑機的加工速度應適當放慢。

Before processing, it is necessary to remove the dust or foreign matters on the surface of the plate to avoid leaving scratches or nicks on the surface of the plate. In addition, the processing speed of the router should be kept at 2m/min. If the angle of the router blade is small and the thickness of the workpiece is thick, the processing speed of the router should be slowed down appropriately.

另外，銑刀刃的長度應該大于加工件的厚度，這樣可以保證一次走刀就能銑削出邊緣的線型。走刀時，鏤銑刀從高處逐步向低處下滑，直至鏤銑刀刃包容銑削邊緣。

In addition, the length of the milling cutter edge should be greater than the thickness of the workpiece, so as to ensure that the line shape of the edge can be milled in one pass. When walking, the router gradually slides from high to low until the router edge covers the milling edge.

值得注意的是，走刀時，一定要保持平穩，不要讓鏤銑機晃動?；蝿訒构ぜ倪吘壭纬刹灰?guī)則波紋，給后續的砂磨拋光工序增加工作量，影響加工效率。

It is worth noting that when walking the knife, you must keep it steady and don't let the router shake. Shaking will make the edge of the workpiece form irregular waves, which will increase the workload of the subsequent sanding and polishing process and affect the processing efficiency.

抗倍特板在安裝結束時，如果表面出現斑點或污跡，可用毛巾沾取少量油性清潔輕輕擦拭去這些斑點或污點。如果沒有斑點或污跡，用一般清潔劑如肥皂加水，或洗潔精加水擦拭即可。更多相關內容就來我們網站http://www.www77mmnncom.cn咨詢看看吧！

At the end of installation, if there are spots or stains on the surface of the anti beta plate, use a towel to dip a small amount of oily cleaning and gently wipe them off. If there are no spots or stains, use general detergent such as soap and water, or detergent and water to wipe. Come to our website for more relevant content http://www.www77mmnncom.cn Consult and have a look!