木紋防火板施工流程底層防潮處理→放線→骨架連接件固定→固定龍骨→底層板裝置→裝置飾面防火板，若隔斷墻內有管線裝置則應在封罩面板之前完結。隔斷墻上有插座等物件，則應在相應方位設加強墊木。

The construction process of wood grain fireproof board includes bottom moisture-proof treatment → laying out → fixing the skeleton connectors → fixing the keel → bottom board installation → installing decorative fireproof board. If there is a pipeline installation inside the partition wall, it should be completed before sealing the panel. If there are sockets or other objects on the partition wall, reinforced wooden pads should be installed in the corresponding positions.

底層板和飾面防火板的裝置底層板防潮處理：為了避免墻面的潮氣使夾板發生翹曲，墻面應采取防潮措施。其辦法有兩種：一種在底層上先做防潮砂漿抹灰，干燥后再涂一道防水涂料如1mm涂膜橡膠；另一種是在墻面比較干燥的情況下，采用護墻面板與墻面之間通氣，即在罩面板的上、下留透氣孔，保證墻龍骨、飾面板干燥。

The installation of bottom board and decorative fireproof board: In order to prevent moisture on the wall from causing warping of the plywood, moisture-proof measures should be taken on the wall. There are two methods: one is to first apply moisture-proof mortar on the bottom layer, dry it, and then apply a waterproof coating such as 1mm coated rubber; Another method is to use ventilation between the wall panel and the wall when the wall is relatively dry, that is, to leave air holes on the top and bottom of the cover panel to ensure the dryness of the wall keel and decorative panel.

放線：放線前要檢查墻面的質量情況，彈出豎筋和橫筋的龍骨裝釘垂直線和水平線。其墻筋的距離應參照罩面板的長、寬規格尺度確定。 木骨架固定；墻體內預埋木磚或嵌入木楔，或許用射釘槍射釘將豎向墻筋釘入墻面上見下圖。

Setting out: Before setting out, the quality of the wall should be checked, and the vertical and horizontal lines of the vertical and horizontal reinforcement keel should be marked. The distance between its wall reinforcement should be determined based on the length and width specifications of the cover panel. Fixed with wooden frame; Embed wooden bricks or wedges into the wall, or use a nail gun to nail the vertical wall reinforcement into the wall, as shown in the following figure.

橫豎墻筋的距離按放線釘好 裝置夾板底層；龍骨裝置完結后，將底層夾板依照龍骨距離并依據底層板的規格進行排板，并用鐵釘進行裝置固定，要求固定牢固，釘帽要隱入板內不得漏出釘頭；要求襯板外表無翹曲、起皮現象，外表平整、清潔，板與板之間縫隙應在豎木筋處。

The distance between the horizontal and vertical wall reinforcement is determined by setting out and nailing the device to the bottom layer of the clamping plate; After the completion of the keel installation, the bottom layer plywood should be arranged according to the distance between the keel and the specifications of the bottom layer board, and fixed with iron nails. The fixation should be firm, and the nail cap should be hidden inside the board without leaking the nail head; The lining board should have no warping or peeling on the surface, be flat and clean, and the gap between the boards should be at the vertical wooden bars.

本文由富美家裝飾耐火板提供技術支持，更多的詳細精彩內容請點擊我們的網站http://www.www77mmnncom.cn，我們將會全心全意為您提供滿意的服務。

This article is supported by Fumeijia Decorative Refractory Board. For more detailed and exciting content, please click on our website http://www.www77mmnncom.cn We will wholeheartedly provide you with satisfactory service.